- #ELECTRONIC SENTRY SAFE OPEN INSTALL#
- #ELECTRONIC SENTRY SAFE OPEN MANUAL#
- #ELECTRONIC SENTRY SAFE OPEN CODE#
It is not recommended to attempt to bolt to both floor and wall. Set the safe in place and use the holes provided in the bottom or back of the safe to mark the location of the holes to be drilled in the floor or wall.
Select a suitable and convenient location for your safe. In this mode, the lock cannot be activated and any key entry will generate an ERROR signal. 
#ELECTRONIC SENTRY SAFE OPEN CODE#
The lock automatically enters a two-minute Delay Mode after an invalid code has been entered three consecutive times. NOTE: When changing the batteries, you must use the factory code to open (See back cover.) Passcode will have to be re-programmed. (Note: When the new batteries are installed, the Yellow LED may come ON and stay ON during the first lock operation before it returns to OFF.) (The lock will continue to function in a Low Battery state, until battery failure.) The Yellow LED will turn OFF only after three consecutive “Good Battery” readings or after the low batteries are replaced.
If a “low battery” condition is detected, the Yellow LED will come ON and remain ON during each subsequent lock operation. Your electronic lock automatically performs a low battery test during each lock use. Indicates “low battery” and will typically not turn OFF until new alkaline batteries are installed. User Code and remains ON until you have entered a 5-digit passcode.
Comes ON in the Program Passcode mode after you have entered your. Comes ON in the Program User Code mode after you enter the Factory Code and remains lit until you have finished entering a 5-digit User Code. Comes ON after you enter a valid code/passcode and remains lit during the 4-second period in which the safe can be opened. After entering each digit of Factory or User Code, or Passcode. You have let 5 seconds or more elapse between key entries. 
You have entered an invalid code or passcode. You have pressed Program key out of sequence. Red (Error) LED + three beeps indicates one of the following: Your electronic-lock safe communicates by means of several audio/visual signals. Unlock the door by inserting the key provided into the hole and turning clockwise. Remove the keypad by rotating the cover counterclockwise, then pull toward you. If your electronic lock fails or you do not have any codes available, you may use a key override to access this unit. (If you realize you have made an error while entering your code, press the CLEAR button and start over.) Key override If you fail to do so in time, the lock will reactivate. Once you have done this, you have 4 seconds to open the safe by turning the handle or 4-bitted key to the unlock position. To unlock the safe, you must enter a valid Factory Code, User Code or Passcode. To erase the passcode, press Program twice, enter your User Code and then enter 00000.) Unlocking (To enter a new passcode, repeat these steps. Enter the 5-digit passcode of your choice (any combination except 00000.) After 5 digits are entered, the green LED turns OFF. (To enter a new User Code, repeat these steps.) Programming a passcode The lock will “beep” and the green LED will come on. (To enter a new User Code, repeat these steps.) After 5 digits are entered the green LED turns OFF. The green LED remains ON while you enter the 5-digit user code of your choice. There are two ways to program a user code. If you wish to give someone else temporary access to the safe, you can program a passcode that can later be erased. But if you prefer to use your own code, you can program the safe to open to the 5-digit User Code of your choice. You can always open the safe by entering the 5-digit Factory Code. There are three possible ways to unlock and access the safe-by entering its preset Factory Code, your own User Code or a Passcode. If you pause longer, an error signal will occur (blinking red light and three beeps), indicating you should start over. The lock allows 5 seconds for each key press. A green PROCEED light and a single beep indicate that the keypad “felt” your touch. For units with key, turn the key to the right. 
(Be sure key lock is turned as far left as possible.) Insert the four-bitted key into the lock to the left of the key pad.Some electronic units are equipped with a handle OR electronic lock and key. NOTE: All electronic lock units have been provided with an override key (skeleton key). Test your combination several times with the door open.
#ELECTRONIC SENTRY SAFE OPEN MANUAL#
(See back cover of this manual for your factory code.) B) Insert the four batteries as indicated. Remove key hook plate located on the inside back of the door by sliding the plate upward, then pulling toward you. A) Unlock door with the override key provided in the plastic bag attached to the owner’s manual, and open the door using the lever handle.
#ELECTRONIC SENTRY SAFE OPEN INSTALL#
To install batteries, remove keypad by rotating the cover counterclockwise, then pulling toward you.
0 kommentar(er)
